4750 BGN
17.5 KG
2017
250 BGN
![Dartmoor Trail Two Chain guide [2014]](https://ridetracking.com/media/zoo/images/dartmoor-trail-two-chain-guide-2014_4c0691b61977b1e5b722caace616c4c2.jpg "Dartmoor Trail Two Chain guide [2014]")
×
Do it Yourself projects - everything you made / modified / invented by yourself.
DIY autopilot GoPro Drone - RC Multicopter Buldlog
9 години 2 месеца ago - 9 години 2 месеца ago #14
от Stuyo
Stuyo replied the topic: DIY autopilot GoPro Drone - RC Multicopter Buldlog
Quanum Trifecta Frame assembly + Baby Beast motor mounting + Afro ESC mounting and testfit:
Resources:
1. Baby Beast outrunner - Multistar V2 2206-2150KV Motor The "Baby Beast" (V2)
2. Afro ESC 12A - Afro ESC 12Amp Ultra Lite Multi-rotor Motor Speed Controller (SimonK Firmware) Version 3
3. MG Servo - Turnigy TGY-9018MG Metal Gear Servo 2.5kg/13g/0.10
Resources:
1. Baby Beast outrunner - Multistar V2 2206-2150KV Motor The "Baby Beast" (V2)
2. Afro ESC 12A - Afro ESC 12Amp Ultra Lite Multi-rotor Motor Speed Controller (SimonK Firmware) Version 3
3. MG Servo - Turnigy TGY-9018MG Metal Gear Servo 2.5kg/13g/0.10
Please Вход to join the conversation.
9 години 2 месеца ago - 9 години 2 месеца ago #15
от Stuyo
Stuyo replied the topic: DIY autopilot GoPro Drone - RC Multicopter Buldlog
HKPilot Micro PDB - Power distribution module, cable routing:
Micro HKPilot Mega PDB, BEC and Volt/AMP Sensor 30.5mm Mounting
Micro HKPilot Mega PDB, BEC and Volt/AMP Sensor 30.5mm Mounting
Please Вход to join the conversation.
9 години 2 месеца ago - 9 години 2 месеца ago #16
от Stuyo
Stuyo replied the topic: DIY autopilot GoPro Drone - RC Multicopter Buldlog
HKPilot Mega Micro controller Arducopter board put in a modified CC3D plastic HK case - cut wit saw, sanded and cutouts with exacto knife:
Resources:
1. HKPilot Mega Micro APM - Micro HKPilot Mega Micro Sized Flight Controller and Autopilot with Leads 2.7.2 (APM)
2. CC3D plastic case - Openpilot CC3D Flight Controller Protective Case
Resources:
1. HKPilot Mega Micro APM - Micro HKPilot Mega Micro Sized Flight Controller and Autopilot with Leads 2.7.2 (APM)
2. CC3D plastic case - Openpilot CC3D Flight Controller Protective Case
Please Вход to join the conversation.
9 години 2 месеца ago - 9 години 2 месеца ago #17
от Stuyo
Stuyo replied the topic: DIY autopilot GoPro Drone - RC Multicopter Buldlog
The GPS module is not direct so i had to cut a piece of 2mm soft plastic.
First, cut 25mm square hole for the GPS body, then cut outside and drill holes for mounting:
Resources:
Micro HKPilot GPS And Compass u-Blox NEO-6 and HMC5883
First, cut 25mm square hole for the GPS body, then cut outside and drill holes for mounting:
Resources:
Micro HKPilot GPS And Compass u-Blox NEO-6 and HMC5883
Please Вход to join the conversation.
9 години 2 месеца ago - 9 години 2 месеца ago #19
от Stuyo
Stuyo replied the topic: DIY autopilot GoPro Drone - RC Multicopter Buldlog
Controller installation, GPS, Telemetry and telemetry protection cover:
Resources:
Micro HKPilot Telemetry radio Set With Integrated PCB Antenna 433Mhz
Resources:
Micro HKPilot Telemetry radio Set With Integrated PCB Antenna 433Mhz
Please Вход to join the conversation.
Time to create page: 1.011 seconds
